Відео

My actuator clicks during and after I turn off my Impala. I think it is draining the battery. The car jumps easy with portable charger. I drive for a while. Turn off the car. Go shopping then come back out and the car won't start. Then the clicking noise happens even then. I am so confused. My voltage on the battery is 12.4 and goes up to 14.3 when running. The alternator checks out fine too. Don't know what it is...frustrating. thank you for getting me closer to a solution!

I'm watching again and I want to say that's the work of a survivor. Meaning you used your friggin head. You know there's videos that have you do more or less then what you should do. I found that out when I seen people removing way too much to install a Mustang radio or replace a headlight! Thanks!

Great video and ditto on most of the top positive comments. The tips like "extra wrenches" and a "towel to keep things in place" are invaluable to pros and DIYers alike. Thanks.

Great idea! Did you have the link to take apart the shifter? Thanks

Nail polish remover is way way way faster than

No one will watch ur video more than 30 sec ur voice is so irritating

Carbon buildup on intake valves caused by condensing blowby gases via PCV is the plague of GDI engines (like Kia & Hyundai). If this works as claimed, it should prevent 95% of that buildup on a continual basis, rather than periodic service to remove it. Has ayone considered this?

Great voice, but boy do you talk a lot

So funny and still informative.

Instead of cutting off the bottom bracket I just took out the stud and nut it attaches to.

This is the funniest, most useful video I've seen. Thanks for not being boring!! (I need some PBR, though)

I really enjoyed reading the comments because all the professional HVAC guys got triggered. If HVAC companies didn't charge $200/Hr for labor and mark up parts and refrigerant 3X, then people wouldn't try to DIY the fix. I DIY'd my own 24 year old R22 system. I got my EPA 608 Type 2 cert via SKillCat, bought 5 lbs of R22 for $219, a set of Yellow Jacket gauges for $150 and $10 bubble leak liquid. I was lucky and my leak was a bad Schrader valve which I replaced with a $25 core removal tool and new brass caps. I recharged using superheat since it is a piston system. Total cost was $450 and I have a set of tools to use when I eventually do a unit replacement.

I wanna fix mine but the idea of taking it apart scares me because what if I somehow mess something up trying to put it back together?

What a voice! Great instruction. Let's hope I don't "die of embarrassment" at the hospital tomorrow after attempting this repair. 🙂

Great video Merv, I tried the link for the fitting and the page doesn’t exist anymore. Do you have any other links, or information about the fitting (Ryobi p/n, size, thread size/type,etc), or any other alternative? Thank you for your time.

A more secure way to capture the nut you had the magnet on is to get a small piece oh insulation tape and put it on the inside of your socket then push it onto the nut/bolt you are undoing or fitting and it is a nice snug fit. Regards Chris

Where is full length video?🤔

😂 love the humor

This is exactly what I needed to see. Thank you for the great humor and detailed video. I will do just what you have done. Thanks again I will watch more like this. Don't worry - I will send flowers :) ha ha ha.. thank you

Best video ever. Your cool af

Did this work for anybody?

Lol I am actually sitting on the toilet dropping a duce and prepping to go clean the intake on my wife's 2011 prius

Thank you. I noticed one other video's by someone else ignored the indicator dot. I told them too about that. Lol

Thx You gave me a lot of ideas 💡 😮

Thank you so much

Best videos on YT!! ASMR, Dad jokes and a ton of great tutorials. Tackled the EGR cleaning and air intake cleaning. Not easy but just take your time and follow this fine gentleman’s videos. Good bless you mate. Thank you 🙏

this man's voice alone gave me faith

A word to the wise...after fighting with the "expendable crew member" for a day and a half, I came up with a brainstorm that maybe my tool was too big (no pun intended) because of this hose that's right next to it that prevented me from getting a 12mm deep well and 3/8 drive ratchet in there. So I ran to Napa and got me a 12mm 1/4" drive deep well socket along with a 3" and 6" extension just in case and with the help of my long handled 1/4" drive ratchet, I had it out in a matter of minutes

Awesome video thanks

Come home to SIMPLE RICKS....

...adorable but venomous...YEP - WEAR GLOVES! - and, NO, not the cute cotton ones that come with the saw...

@3:30 (round things sitting on flat surfaces roll away) Put a 2" long piece of electrical tape around the middle of the rod (making a little tab on the side where the two ends of tape meet) will stop them from misbehaving.

Your videos are excellent

Where is a good source for new parts

Wow, this was a very informative, entertaining video. The voice of Dukes of Hazard, tv show, just dated myself. Thank you so much, the tip of sawing off that little pestie bracket was the highlight for me. I've been waiting for months to tackle this project and now with your video and others I've watched, i think I'm ready. Thanks uncle Jesse, was that his voice?

I just came to listen to you talk your accent is fantastic..

This video help me a lot but voice should be on a terror film at Hollywood 🤣👍

so true ....i thought it was me doing something wrong!

you had me at PBR ,,,

A/c running. Motor runs most of the time but sometimes it doesn’t. But compressor will be. The evaporator then freezes up. At that point I turn off ac, I turn on manual fan and it won’t come on either. It seems after it sits, the ice thaws I can then press fan again it then works. At that point I turn ac back in and it works fine. Can’t find the rhyme or reason. The motor is maybe 2-3 years old, just replaced capacitor thinking it was the issue. But it continues to randomly not work. I’m Replacing thermostat cause it’s 24 years old. But a hvac guy told me if I hit box and blower starts then it was a certain thing but I can’t remember what he said. I went under house watched. The outdoor unit started but blower didn’t. I hit the box with my hand and it started blowing high speed.

PCV doesn't route exhaust to the intake, that's the PCV's job. The small amount of exhaust that gets passed the rings will go to the intake, but no catch can is going to change that, even this fancy one. Comparing one's achieved mileage to the EPA estimated mileage is useless in determining that this device is helping, you need your achieved MPG before and after installing it. I can't imagine how cleaning the PCV air increases MPG, I'd love to see actual evidence. Tracy's statement about 'normal' catch cans being no more than 15-20% effective is complete BS.

You're funny as heck and make it look easy. Thanks. Do you have a video about the oil leak on the back left (passenger) side? I'm not exactly sure where the oil is coming from but I figure it's probably a common problem.

Merve… I came across your channel when I was trying to restring a weedeater. You remind me of my grandpa and I am so happy to have found your channel. He passed away many years ago, but when I watch your videos, it’s like he’s sitting beside me again all the woodwork, all the building all the tool maintenance and how to enjoy myself. Thank you for your channel.

Thank you!!!

Lol "make sure to clean your crack with some rubbing alcohol" damn, that's gotta sting! Good job brotha! 😂

I always clean my crack out with rubbing alcohol.

HEllo ! I've got a prius 2nd gen.,but your video is soo well done that I litereally watched it until the end, by pleasure. Bravo !

Man I’m having the hardest time getting that damn stud off the bottom! Like I’ve been trying for days can’t get my egr cooler off 😭

Never mind. Next video.. I might as well go to mechanic School. Sh! T all this time.

C'mon man with all that Tim the tool man from next door, not looking over the gate